關于我(Wǒ)們 About us
安力博機械(Xiè)
青島安力博機械設備有[Yǒu]限公司是一家專業代理銷售◈全◈球知[Zhī]名品牌機械、進口工具(Jù)的公司(Sī),公司∇主∇(Zhǔ)營産品有液壓工具、電動[Dòng]工●具●、氣動工具等各(Gè)種進[Jìn]口工具及機械(Xiè)。
聯系[Xì]我們 Contact us
地址:青島市李[Lǐ]滄◇區◇九水路225号[Hào]
電話[Huà]:0532-6661 0139
傳○真○:0532-8666 6968
郵箱:ienerpac@163.com
網址:www.u6080.cn
24小時服務電話:135 7387 5130
——全國服務熱線——
0532-6661 0139
當前位○置○:首頁>>技術服務技術服務

螺栓[Shuān]螺母理論

發布[Bù]時間[Jiān]:2017-03-03   點擊:669次

Function of Bolts and Nuts

Threaded fasteners are used across industry to assemble products ranging from pipelines to heavy-duty
earth movers and from cranes and bridges and many more. Their principle function is to create a clamping
force across the joint which is able to sustain the operating conditions without loosening.

Correctly tightened bolts make use of their elastic properties, to work well they must behave like springs.
When load is applied, the bolt stretches and tries to return to its original length. This creates compressive
force across the joint members.



 
Behavior of Bolts and Nuts
Elasticity is defined in Hooke's Law of Physics: The stress in a bolt is directly proportional to its strain. The stress-strain of a bolt has an elastic range and aplastic range. In this elastic range Hooke's Law is true.

All of the elongation applied within the elastic range is relieved when the load is removed. The amount of elongation increases when more load is applied. When a bolt is stressed beyond its proof load (maximum load under which a bolt will behave in an elastic manner), the elastic elongation changes to plastic deformation and the strain will no longer be proportional to stress.
In the plastic deformation a part of the elongation will remain after the load is removed. The point where this permanent elongation occurs is called the yield strength. The further application of load takes the bolt to a point where it begins to fail this is termed its ultimate tensile strength (UTS). At this UTS-point, if additional force is applied to the bolt it will continue to elongate until it finally breaks. The point at which the bolt breaks is called the tensile point.

Careful attention must be paid to the grade of bolt being used as bolt grades differ in the elastic range.

 
Preload
The main purpose of a bolt and nut is to clamp parts together with the correct force to prevent loosening in operation. The term preload refers to the loading in a bolt immediately after it has been tightened.

The amount of preload (residual load) is critical as the joint can fail if the load in the bolt is too high, too low, or not uniform in every bolt.

Uneven bolts can result in:
  • Some bolts being loose while others are overloaded.
  • Crushing of the gasket on one side, leakage on the other side.

Preload is normally dictated by the joint design, (see Enerpac Bolted Joint Integrity) for information on common joint types or contact your local representative.

Tightening Methods

Principally there are two modes of tightening: "Uncontrolled" and "Controlled".

Uncontrolled Tightening
Uses equipment and/or procedures that cannot be measured. Preload is appllied to a bolt and nut assembly using a hammer and spanner or other types of impact tools.

Controlled Tightening
Employs calibrated and measurable equipment, follows prescribed procedures and is carried out by trained personnel. There are two main techniques: Torque tightening and Bolt Tensioning.

1. Torque Tightening - Achieves preload in a bolt and nut assembly via the nut in a controlled manner using a tool.
2. Bolt Tensioning - Achieves preload in a bolt and nut assembly by stretching the bolt axially using a tool.

Sitemap